[Vac] - Electrical Engineer - Maintenance for Kuwait

We are looking for Electrical Engineer (Maintenance) for a long term contract (12-24 months) for our Client, a European MNC, for their projects in Kuwait.

Candidate should be BE or Diploma in Electrical with relevant experience of 5 - 10 years in Power Transmission & Distribution sector. Candidate has to perform preventive maintenance , emergency work , repair for installation type B65 - B95 - T65 - C65 - S105 - B105 and make retrofit, overhauling. At least 5 years experience on Areva / Alstom Equipments like Gas Insulated Substations / Switchgears (GIS) is a must.

Job Profile details are as follows:

1 - General Knowledge:

- Risks and means of prevention linked with handling/work at height/electrical current/use of pressurized tank/SF6 gas
- Principle of operation of GIS equipment
- Reading an assembly drawing
- Reading an installation drawing/a cable routing drawing
- Principle of operation of hydraulic mechanisms
- Principle of operation of Local Cubicle Control
- Principle of operation of Spring Operating Mechanism
- Principle of operation of Earthing Switch
- Operation's process on contaminated compartments
- Test Sheet and Reporting


2 – Standard maintenance

- M2 procedure
- M4 procedure with hydraulic mechanism
- M4 procedure with spring mechanism


3 – Main actions for M2 maintenance of GIS installation:

- Compartments Gas inspection :
·SF6 pressure measurement
·Moisture content : dew point , ppm value
·SF6% measurement
·Acidity and density checking
·SF6 Tightness checking

- Circuit Breaker inspection :
·tripping coil , motor , heater
·filling & bleeding : pump , rams, control piping
·Nitrogen pre-inflation ( accumulator ) : pressure rising and dropping
·Pressure switch thresholds : Pump , closing ( unlocking – locking ) , trip
·Check oil tank level, filter
·Check timing : open, close , tripping ...

- CT and VT checking :
· wiring connection and labeling

- Isolators and E/S mechanical inspection
·manual, electrical checking : open close
·Interlock checking
·Various inspections: heating, wiring connections, rod& shaft …
·Motor current measurement

- Functional test for local cubical
·Isolator. E/S, CB
·Hydraulic alarm and interlock
·Gas monitoring


4 - Mission on station in Service

-Control of safety CHECK-LIST
-Procedure for obtaining a work permit
-Evaluation of the condition of the equipment according of the number of cut-offs
-Dismantling, inspection and re-assembly of all the components using the special tools and according to the instructions.
-Inspection of equipment after dismantling following an incident
-Commissioning and specific test after intervention
-Material needs definition for a repair


5 - Specific Operations on a Major Failure

- Circuit Breaker, Disconnector, Earthing Switch, Other GIS devices:
·Knowledge of the lubrication procedure
·Removal and installation of the breaker pole from/into the Bay.
·Life Part removal from tank using special tools
·Commissioning and specific testing after major examination
·Location of Flashover
·Dismantling, inspection and re-assembly of the various Life Part components
·S02 Measures - Knowledge of the levels acceptance - Results interpretation
·Diagnostic of GIS internal parts
·Diagnosis after a flashover


- HYDRAULICS
·Detailed knowledge of the operation of Mechanisms
·Using the Special Tools remove from the cubicle the components to be overhauled
·Dismantling, inspection and re-assembly of all the components of the ram using the special tools and following the instructions
·Dismantling and installation of hydraulic pipe systems
·CH2, CH3 & CH4 Mechanisms: Dismantling, inspection and re-assembly of all the internal components using the special tools and following the instructions.
·Commissioning and specific testing after a major examination
·Troubleshooting


- SPRING MECHANISMS
·Knowledge of the operating principle
·Knowledge of the lubrication method
·Use of specific tools
·Knowledge of the measurement method on dashpot, roller play & over travel
·Adjustment of the breaker timing
·Dismantling, inspection evaluation of mechanical wear, re-assembling & adjustment
·Troubleshooting


If your profile matches our requirement, Please send your detailed updated CV in Word Format to epcengg@gmail.com along with following details for faster CV processing:

Current Location:
Current Salary:
Expected Salary:
Joining Time:

Please inform your Friends & Colleagues about this opening who fit our required profile and are worth recommending as per your opinion.

Thank You & Regards,

Team Aarvi
VISIT (Re-type Links Address on your Browser):
www.gasoiljobs.co.cc
www.oilandgas-jobs.co.cc
www.oilgasjob-s.co.cc
www.oil-trading.co.cc